10 Peg Board Receivers ( Vertical Wall Model) (Pegs included)

4 review(s) | Add your review

$222.88

Screw on and pegboard on!

Hardware *
Single Hold Colors *

Overview
Reviews

Traditional wood Pegboards wear out. The leverage from the peg eventually reams the hole, making the board substantially harder. Thus, the board itself is the weak point in pegboards. With Atomik's Pegboard Receivers, that will never happen as this product is manufactured out of premium grade resin and attaches to the face of your wall surface.

Atomik's Pegboard Receivers also gives you a bonus of being able to campus outside the Receiver. The "ball" part of this product measures 4-1/2" diameter, which feels like an incut sloper. If you can Pegboard, you can campus on the outside of the ball.

You get both the inserting of the wood peg, which trains the "hammer fist" grip position, and the outside, which introduces open-handed sloper training.

To install this product, attach them will #10 through-bolts. If you do not have access to behind your panel, you can secure them with #10 screws. Using a Structural Wood Screw does work; however, wood screws tend to loosen, especially when the athletes are over 200 pounds. Our advice is to install using the following HARDWARE. This specific length works for installation on a 3/4" plywood panel.

The Pegboard Receiver measures 4-1/2" in diameter x " standing off the wall. The hole where the wood peg inserts are machined at 1-5/16" to receive the 1-1/4" hardwood dowels which are included.

The 1-5/16" hole is a 2-3/4" deep hole.

Install the Vertical Model Pegboard Reciever on a vertical surface only. When installed on a vertical surface, the hole where the wood peg inserts is parallel to the ground. The 1-1/4" peg inserts and removes freely.

Check out Atomik's other Pegboard Products.

SIZE: The RECEIVER measures 4-1/2" diameter x 3-1/8" standing off the wall.
SIZE: The HOLE in the Receiver measures 1-5/16" x 2-3/4" deep.
TEXTURE: The texture offers a grip that is skin-friendly and feels like natural rock.

easy to install pegboard

These receivers work great mounted onto a 2x6 or 2x8 board. They differ from a traditional pegboard in a couple significant ways: 1. they require more accuracy when placing the pegs into the holes because you don't have a flat surface to poke around on before finding the hole; 2. the pegs rotate in the holes more than a traditional wooden pegboard. These therefore work the grip more because you can't just place a peg and hang on it.

I don't really train on them as sloper holds because the holes hit my hands where I've got big old calluses so it's not comfortable for me.

Date: 5/16/2018 6:02 PM

Was this review helpful? Yes No (2/0)

These are great!

I hung these from the rafters of my basement ceiling, upon which I’ve also installed footholds. Allows me to use these for roof climbing, as well as hanging from arms only. Excellent forearm workout, gets you pumped quick! I like to use these to warm up for routes with more difficult holds, as well as for ARC training. So easy to install, and also great as standalone slopers.

Date: 6/30/2020 11:37 PM

Was this review helpful? Yes No (0/0)

Quick To Install

These are great because they are easy to install. They are also nice because you can configure they however you would like to. They are better than your standard peg board because the holes wont bore out like your average wood peg board. They are also nice for sloper training.

Date: 9/25/2020 5:36 PM

Was this review helpful? Yes No (0/0)

Anywhere Pegboard

Customization and Versatility are what you are buying here.
-Put a pegboard any (and every) where you want. Set up your own pattern, and distance. Plus, the receivers double as climbing holds for a great warm-up or a way to continue the workout after you've toasted your forearm/grip strength with the pegs.
-Make sure you buy a few harder pegs to go along with this because the hope is that one day you'll need them.

Date: 4/2/2021 8:40 AM

Was this review helpful? Yes No (0/0)

You get both the inserting of the wood peg, which trains the "hammer fist" grip position, and the outside, which introduces open-handed sloper training.

The Pegboard Receiver measures 4-1/2" in diameter x " standing off the wall. The hole where the wood peg inserts are machined at 1-5/16" to receive the 1-1/4" hardwood dowels which are included.

The 1-5/16" hole is a 2-3/4" deep hole.

Check out Atomik's other Pegboard Products.

SIZE: The RECEIVER measures 4-1/2" diameter x 3-1/8" standing off the wall.
SIZE: The HOLE in the Receiver measures 1-5/16" x 2-3/4" deep.
TEXTURE: The texture offers a grip that is skin-friendly and feels like natural rock.

Product tags

Also Bought

10 Peg Board Receivers ( Vertical Wall Model) (Pegs included)

T-nut (Round Base Zinc)

Bolt On Campus Rung 2" 80/90

Ring Toss Peg

Block chalk

Large Ring 1-1/4" ( Down Climbing Hold )